إعـــــــلان

تقليص
لا يوجد إعلان حتى الآن.

نظام اوبونتو عندي لا يتعرف على الpen drive

تقليص
X
 
  • تصفية - فلترة
  • الوقت
  • عرض
إلغاء تحديد الكل
مشاركات جديدة

  • [مشكلة] نظام اوبونتو عندي لا يتعرف على الpen drive

    بسم الله الرحمان الرحيم
    أرجو من الإخوة أن يساعدوني في هذه المشكلة
    فلا يمكنني فعل أي شيء دون الpen drive kingstone
    1 - نظام الويندوز عندي يتعرف عليها
    2 - نظام الاوبونتو عندي لا يتعرف عليها
    3 - في الأجهزة الأخرى نظام الاوبونتو يتعرف عليها
    فما الحل

  • #2
    صادفت بعض الأجهزة التي تعطي نفس المشكلة مع بعض موصلات usb بالإزدواجية إستخدام usb1.1 و usb2.0 رديئة من ناحية اتباعها للمواصفات أو بسبب التعريف الذي يتوه بين استخدام النمطين. هناك سبب ثالث لكنه لا ينطبق على حالتك و هو عدم قدرة بعض لواحة الأم تغدية موصل usb بالشكل الكافي.

    الحل مع تلك الأجهزة هو وصل الـ pen drive usb على الموصلات التي توجد في خلفية صندوق الجهاز بدلا من التي توجد في الواجهة.
    ArabicFOSS
    انضم إلى فريق المدونة و ساهم بما شئت وقتما شئت!

    تعليق


    • #3
      المشاركة الأصلية بواسطة محمد البردعي مشاهدة المشاركة
      صادفت بعض الأجهزة التي تعطي نفس المشكلة مع بعض موصلات usb بالإزدواجية إستخدام usb1.1 و usb2.0 رديئة من ناحية اتباعها للمواصفات أو بسبب التعريف الذي يتوه بين استخدام النمطين. هناك سبب ثالث لكنه لا ينطبق على حالتك و هو عدم قدرة بعض لواحة الأم تغدية موصل usb بالشكل الكافي.

      الحل مع تلك الأجهزة هو وصل الـ pen drive usb على الموصلات التي توجد في خلفية صندوق الجهاز بدلا من التي توجد في الواجهة.
      جربت لكن نفس المشكل .

      تعليق


      • #4
        جيد، لنرى ما هي مخرجات الأوامر التالية:
        كود:
        lsusb
        كود:
        lspci | grep USB
        كود:
        sudo fdisk -l
        كود:
        dmesg | grep USB
        ثم اسحب الـ usb و نفد ما يلي ثم صلها من جديد:
        كود:
        sudo modprobe usb-uhci
        sudo modprobe usb-ohci
        sudo modprobe usb-storage
        ArabicFOSS
        انضم إلى فريق المدونة و ساهم بما شئت وقتما شئت!

        تعليق


        • #5
          المشاركة الأصلية بواسطة محمد البردعي مشاهدة المشاركة
          جيد، لنرى ما هي مخرجات الأوامر التالية:
          كود:
          lsusb
          كود:
          lspci | grep USB
          كود:
          sudo fdisk -l
          كود:
          dmesg | grep USB
          ثم اسحب الـ usb و نفد ما يلي ثم صلها من جديد:
          كود:
          sudo modprobe usb-uhci
          sudo modprobe usb-ohci
          sudo modprobe usb-storage
          ها هي المخرجات يبدو أنه لا يتعرف عليها
          [email protected]:~$ lsusb
          Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
          Bus 004 Device 006: ID 1bcf:0007 Sunplus Innovation Technology Inc.
          Bus 004 Device 002: ID 1c4f:0002 SiGma Micro
          Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
          Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
          Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
          Bus 001 Device 008: ID 12d1:140c Huawei Technologies Co., Ltd.
          Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
          [email protected]:~$ lspci | grep USB
          00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
          00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
          00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
          00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
          00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
          [email protected]:~$ sudo fdisk -l
          [sudo] password for assilah:

          Disk /dev/sda: 40.0 GB, 40020664320 bytes
          255 heads, 63 sectors/track, 4865 cylinders
          Units = cylinders of 16065 * 512 = 8225280 bytes
          Sector size (logical/physical): 512 bytes / 512 bytes
          I/O size (minimum/optimal): 512 bytes / 512 bytes
          Disk identifier: 0x000cf05f

          Device Boot Start End Blocks Id System
          /dev/sda1 * 1 2342 18806784 83 Linux
          /dev/sda2 2342 4866 20273153 5 Extended
          /dev/sda5 4683 4866 1466368 82 Linux swap / Solaris
          /dev/sda6 2342 4580 17975296 83 Linux
          /dev/sda7 4580 4683 823296 82 Linux swap / Solaris

          Partition table entries are not in disk order
          [email protected]:~$ dmesg | grep USB
          [ 0.496837] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
          [ 0.496989] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
          [ 0.515284] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
          [ 0.515534] hub 1-0:1.0: USB hub found
          [ 0.515664] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
          [ 0.515695] uhci_hcd: USB Universal Host Controller Interface driver
          [ 0.515846] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
          [ 0.516091] hub 2-0:1.0: USB hub found
          [ 0.516279] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
          [ 0.516530] hub 3-0:1.0: USB hub found
          [ 0.516704] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
          [ 0.516956] hub 4-0:1.0: USB hub found
          [ 0.517143] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
          [ 0.517390] hub 5-0:1.0: USB hub found
          [ 0.962196] usb 1-7: new high speed USB device using ehci_hcd and address 4
          [ 1.123609] Initializing USB Mass Storage driver...
          [ 1.123919] scsi4 : SCSI emulation for USB Mass Storage devices
          [ 1.124321] scsi5 : SCSI emulation for USB Mass Storage devices
          [ 1.124645] USB Mass Storage support registered.
          [ 1.348019] usb 4-1: new low speed USB device using uhci_hcd and address 2
          [ 1.598431] input: USB USB Keykoard as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input3
          [ 1.598636] generic-usb 0003:1C4F:0002.0001: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keykoard] on usb-0000:00:1d.2-1/input0
          [ 1.800024] usb 4-2: new low speed USB device using uhci_hcd and address 3
          [ 11.614125] input: USB USB Keykoard as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.1/input/input4
          [ 11.614279] generic-usb 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Device [USB USB Keykoard] on usb-0000:00:1d.2-1/input1
          [ 11.631292] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input5
          [ 11.631487] generic-usb 0003:1BCF:0007.0003: input,hiddev96,hidraw2: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.2-2/input0
          [ 11.631524] usbhid: v2.6:USB HID core driver
          [ 20.422136] usb 1-7: USB disconnect, address 4
          [ 26.500018] usb 1-7: new high speed USB device using ehci_hcd and address 5
          [ 26.650209] scsi10 : SCSI emulation for USB Mass Storage devices
          [ 26.651202] scsi11 : SCSI emulation for USB Mass Storage devices
          [ 26.805717] USB Serial support registered for generic
          [ 26.805982] usbserial: USB Serial Driver core
          [ 26.822634] USB Serial support registered for GSM modem (1-port)
          [ 26.823025] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB0
          [ 26.823214] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB1
          [ 26.824695] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB2
          [ 26.824929] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB3
          [ 26.825360] option: v0.7.2:USB Driver for GSM modems
          [ 8115.946564] usb 1-7: USB disconnect, address 5
          [ 8115.947020] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
          [ 8115.947193] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
          [ 8115.947356] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
          [ 8115.947509] option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
          [ 9012.576021] usb 1-7: new high speed USB device using ehci_hcd and address 6
          [ 9012.711157] scsi12 : SCSI emulation for USB Mass Storage devices
          [ 9186.954266] usb 1-7: USB disconnect, address 6
          [ 9195.068034] usb 1-7: new high speed USB device using ehci_hcd and address 7
          [ 9195.219493] scsi13 : SCSI emulation for USB Mass Storage devices
          [ 9195.219930] scsi14 : SCSI emulation for USB Mass Storage devices
          [ 9201.339209] usb 1-7: USB disconnect, address 7
          [ 9207.796042] usb 1-7: new high speed USB device using ehci_hcd and address 8
          [ 9207.944458] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB0
          [ 9207.944921] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB1
          [ 9207.946476] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB2
          [ 9207.946935] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB3
          [ 9207.947633] scsi19 : SCSI emulation for USB Mass Storage devices
          [ 9207.948493] scsi20 : SCSI emulation for USB Mass Storage devices
          [ 9897.848529] usb 4-2: USB disconnect, address 3
          [ 9898.585036] usb 4-2: new low speed USB device using uhci_hcd and address 4
          [ 9898.772338] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input6
          [ 9898.772927] generic-usb 0003:1BCF:0007.0004: input,hiddev96,hidraw2: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.2-2/input0
          [ 9900.577076] usb 4-2: USB disconnect, address 4
          [ 9900.785083] hub 4-0:1.0: unable to enumerate USB device on port 2
          [ 9902.057050] usb 4-2: new low speed USB device using uhci_hcd and address 6
          [ 9902.241061] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input7
          [ 9902.241344] generic-usb 0003:1BCF:0007.0005: input,hiddev96,hidraw2: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.2-2/input0
          [ 9911.252039] usb 1-3: new high speed USB device using ehci_hcd and address 12
          [ 9911.820054] usb 1-3: new high speed USB device using ehci_hcd and address 13
          [ 9912.388033] usb 1-3: new high speed USB device using ehci_hcd and address 14
          [ 9912.972048] usb 1-3: new high speed USB device using ehci_hcd and address 15
          [ 9913.388057] hub 1-0:1.0: unable to enumerate USB device on port 3
          [ 9913.656048] usb 3-1: new full speed USB device using uhci_hcd and address 2
          [ 9944.201040] usb 3-1: new full speed USB device using uhci_hcd and address 3
          [ 9974.745038] usb 3-1: new full speed USB device using uhci_hcd and address 4
          [ 9985.100043] usb 3-1: new full speed USB device using uhci_hcd and address 5
          [ 9995.344057] hub 3-0:1.0: unable to enumerate USB device on port 1
          [11600.465061] usb 3-1: new full speed USB device using uhci_hcd and address 6
          [11631.009066] usb 3-1: new full speed USB device using uhci_hcd and address 7
          [11661.552039] usb 3-1: new full speed USB device using uhci_hcd and address 8
          [11671.909463] usb 3-1: new full speed USB device using uhci_hcd and address 9
          [11682.153182] hub 3-0:1.0: unable to enumerate USB device on port 1
          [11694.840048] usb 3-1: new full speed USB device using uhci_hcd and address 10
          [11725.386545] usb 3-1: new full speed USB device using uhci_hcd and address 11
          [11755.929059] usb 3-1: new full speed USB device using uhci_hcd and address 12
          [11766.284036] usb 3-1: new full speed USB device using uhci_hcd and address 13
          [11776.529040] hub 3-0:1.0: unable to enumerate USB device on port 1
          [11983.429072] usb 3-1: new full speed USB device using uhci_hcd and address 14
          [12013.972403] usb 3-1: new full speed USB device using uhci_hcd and address 15
          [12044.517042] usb 3-1: new full speed USB device using uhci_hcd and address 16
          [12054.873041] usb 3-1: new full speed USB device using uhci_hcd and address 17
          [12065.117049] hub 3-0:1.0: unable to enumerate USB device on port 1
          [12978.317041] usb 1-3: new high speed USB device using ehci_hcd and address 16
          [12978.884046] usb 1-3: new high speed USB device using ehci_hcd and address 17
          [12983.888032] usb 1-3: new high speed USB device using ehci_hcd and address 18
          [12984.412035] usb 1-3: new high speed USB device using ehci_hcd and address 19
          [12984.676054] hub 1-0:1.0: unable to enumerate USB device on port 3
          [12984.944043] usb 3-1: new full speed USB device using uhci_hcd and address 18
          [12990.940073] hub 3-0:1.0: unable to enumerate USB device on port 1
          [12994.388044] usb 1-4: new high speed USB device using ehci_hcd and address 20
          [12994.957046] usb 1-4: new high speed USB device using ehci_hcd and address 21
          [12995.524041] usb 1-4: new high speed USB device using ehci_hcd and address 22
          [12995.904073] usb 1-4: new high speed USB device using ehci_hcd and address 23
          [12996.320063] hub 1-0:1.0: unable to enumerate USB device on port 4
          [12996.588042] usb 3-2: new full speed USB device using uhci_hcd and address 19
          [13027.132207] usb 3-2: new full speed USB device using uhci_hcd and address 20
          [13057.676047] usb 3-2: new full speed USB device using uhci_hcd and address 21
          [13068.029068] usb 3-2: new full speed USB device using uhci_hcd and address 22
          [13078.272064] hub 3-0:1.0: unable to enumerate USB device on port 2
          [14278.512029] usb 3-2: new full speed USB device using uhci_hcd and address 23
          [14309.057040] usb 3-2: new full speed USB device using uhci_hcd and address 24
          [14339.601076] usb 3-2: new full speed USB device using uhci_hcd and address 25
          [14349.956043] usb 3-2: new full speed USB device using uhci_hcd and address 26
          [14360.200044] hub 3-0:1.0: unable to enumerate USB device on port 2
          [email protected]:~$ sudo modprobe usb-uhci
          FATAL: Module usb_uhci not found.
          [email protected]:~$ sudo modprobe usb-ohci
          FATAL: Module usb_ohci not found.
          [email protected]:~$ sudo modprobe usb-storage

          تعليق


          • #6
            المشاركة الأصلية بواسطة محمد البردعي مشاهدة المشاركة
            جيد، لنرى ما هي مخرجات الأوامر التالية:
            كود:
            lsusb
            كود:
            lspci | grep USB
            كود:
            sudo fdisk -l
            كود:
            dmesg | grep USB
            ثم اسحب الـ usb و نفد ما يلي ثم صلها من جديد:
            كود:
            sudo modprobe usb-uhci
            sudo modprobe usb-ohci
            sudo modprobe usb-storage
            غيرت مدخل الusb hub فكانت النتائج كالتالي وأعتقد أنها أفضل من الأخرى فعلى الأقل أعطت إشارة إلى الkingstone pen drive
            كود:
            [email protected]:~$ lsusb
            Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
            Bus 004 Device 006: ID 1bcf:0007 Sunplus Innovation Technology Inc. 
            Bus 004 Device 002: ID 1c4f:0002 SiGma Micro 
            Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
            Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
            Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
            Bus 001 Device 031: ID 0930:6545 Toshiba Corp. Kingston DataTraveler 2.0 Stick (4GB) / PNY Attache 4GB Stick
            Bus 001 Device 030: ID 12d1:140c Huawei Technologies Co., Ltd. 
            Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
            [email protected]:~$ lspci | grep USB
            00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
            00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
            00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
            00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
            00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
            [email protected]:~$ sudo fdisk -l
            [sudo] password for assilah: 
            
            Disk /dev/sda: 40.0 GB, 40020664320 bytes
            255 heads, 63 sectors/track, 4865 cylinders
            Units = cylinders of 16065 * 512 = 8225280 bytes
            Sector size (logical/physical): 512 bytes / 512 bytes
            I/O size (minimum/optimal): 512 bytes / 512 bytes
            Disk identifier: 0x000cf05f
            
               Device Boot      Start         End      Blocks   Id  System
            /dev/sda1   *           1        2342    18806784   83  Linux
            /dev/sda2            2342        4866    20273153    5  Extended
            /dev/sda5            4683        4866     1466368   82  Linux swap / Solaris
            /dev/sda6            2342        4580    17975296   83  Linux
            /dev/sda7            4580        4683      823296   82  Linux swap / Solaris
            
            Partition table entries are not in disk order
            [email protected]:~$ dmesg | grep USB
            [    0.496837] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
            [    0.496989] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
            [    0.515284] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
            [    0.515534] hub 1-0:1.0: USB hub found
            [    0.515664] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
            [    0.515695] uhci_hcd: USB Universal Host Controller Interface driver
            [    0.515846] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
            [    0.516091] hub 2-0:1.0: USB hub found
            [    0.516279] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
            [    0.516530] hub 3-0:1.0: USB hub found
            [    0.516704] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
            [    0.516956] hub 4-0:1.0: USB hub found
            [    0.517143] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
            [    0.517390] hub 5-0:1.0: USB hub found
            [    0.962196] usb 1-7: new high speed USB device using ehci_hcd and address 4
            [    1.123609] Initializing USB Mass Storage driver...
            [    1.123919] scsi4 : SCSI emulation for USB Mass Storage devices
            [    1.124321] scsi5 : SCSI emulation for USB Mass Storage devices
            [    1.124645] USB Mass Storage support registered.
            [    1.348019] usb 4-1: new low speed USB device using uhci_hcd and address 2
            [    1.598431] input: USB USB Keykoard as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.0/input/input3
            [    1.598636] generic-usb 0003:1C4F:0002.0001: input,hidraw0: USB HID v1.10 Keyboard [USB USB Keykoard] on usb-0000:00:1d.2-1/input0
            [    1.800024] usb 4-2: new low speed USB device using uhci_hcd and address 3
            [   11.614125] input: USB USB Keykoard as /devices/pci0000:00/0000:00:1d.2/usb4/4-1/4-1:1.1/input/input4
            [   11.614279] generic-usb 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Device [USB USB Keykoard] on usb-0000:00:1d.2-1/input1
            [   11.631292] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input5
            [   11.631487] generic-usb 0003:1BCF:0007.0003: input,hiddev96,hidraw2: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.2-2/input0
            [   11.631524] usbhid: v2.6:USB HID core driver
            [   20.422136] usb 1-7: USB disconnect, address 4
            [   26.500018] usb 1-7: new high speed USB device using ehci_hcd and address 5
            [   26.650209] scsi10 : SCSI emulation for USB Mass Storage devices
            [   26.651202] scsi11 : SCSI emulation for USB Mass Storage devices
            [   26.805717] USB Serial support registered for generic
            [   26.805982] usbserial: USB Serial Driver core
            [   26.822634] USB Serial support registered for GSM modem (1-port)
            [   26.823025] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB0
            [   26.823214] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB1
            [   26.824695] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB2
            [   26.824929] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB3
            [   26.825360] option: v0.7.2:USB Driver for GSM modems
            [ 8115.946564] usb 1-7: USB disconnect, address 5
            [ 8115.947020] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
            [ 8115.947193] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
            [ 8115.947356] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
            [ 8115.947509] option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
            [ 9012.576021] usb 1-7: new high speed USB device using ehci_hcd and address 6
            [ 9012.711157] scsi12 : SCSI emulation for USB Mass Storage devices
            [ 9186.954266] usb 1-7: USB disconnect, address 6
            [ 9195.068034] usb 1-7: new high speed USB device using ehci_hcd and address 7
            [ 9195.219493] scsi13 : SCSI emulation for USB Mass Storage devices
            [ 9195.219930] scsi14 : SCSI emulation for USB Mass Storage devices
            [ 9201.339209] usb 1-7: USB disconnect, address 7
            [ 9207.796042] usb 1-7: new high speed USB device using ehci_hcd and address 8
            [ 9207.944458] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB0
            [ 9207.944921] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB1
            [ 9207.946476] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB2
            [ 9207.946935] usb 1-7: GSM modem (1-port) converter now attached to ttyUSB3
            [ 9207.947633] scsi19 : SCSI emulation for USB Mass Storage devices
            [ 9207.948493] scsi20 : SCSI emulation for USB Mass Storage devices
            [ 9897.848529] usb 4-2: USB disconnect, address 3
            [ 9898.585036] usb 4-2: new low speed USB device using uhci_hcd and address 4
            [ 9898.772338] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input6
            [ 9898.772927] generic-usb 0003:1BCF:0007.0004: input,hiddev96,hidraw2: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.2-2/input0
            [ 9900.577076] usb 4-2: USB disconnect, address 4
            [ 9900.785083] hub 4-0:1.0: unable to enumerate USB device on port 2
            [ 9902.057050] usb 4-2: new low speed USB device using uhci_hcd and address 6
            [ 9902.241061] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.2/usb4/4-2/4-2:1.0/input/input7
            [ 9902.241344] generic-usb 0003:1BCF:0007.0005: input,hiddev96,hidraw2: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:1d.2-2/input0
            [ 9911.252039] usb 1-3: new high speed USB device using ehci_hcd and address 12
            [ 9911.820054] usb 1-3: new high speed USB device using ehci_hcd and address 13
            [ 9912.388033] usb 1-3: new high speed USB device using ehci_hcd and address 14
            [ 9912.972048] usb 1-3: new high speed USB device using ehci_hcd and address 15
            [ 9913.388057] hub 1-0:1.0: unable to enumerate USB device on port 3
            [ 9913.656048] usb 3-1: new full speed USB device using uhci_hcd and address 2
            [ 9944.201040] usb 3-1: new full speed USB device using uhci_hcd and address 3
            [ 9974.745038] usb 3-1: new full speed USB device using uhci_hcd and address 4
            [ 9985.100043] usb 3-1: new full speed USB device using uhci_hcd and address 5
            [ 9995.344057] hub 3-0:1.0: unable to enumerate USB device on port 1
            [11600.465061] usb 3-1: new full speed USB device using uhci_hcd and address 6
            [11631.009066] usb 3-1: new full speed USB device using uhci_hcd and address 7
            [11661.552039] usb 3-1: new full speed USB device using uhci_hcd and address 8
            [11671.909463] usb 3-1: new full speed USB device using uhci_hcd and address 9
            [11682.153182] hub 3-0:1.0: unable to enumerate USB device on port 1
            [11694.840048] usb 3-1: new full speed USB device using uhci_hcd and address 10
            [11725.386545] usb 3-1: new full speed USB device using uhci_hcd and address 11
            [11755.929059] usb 3-1: new full speed USB device using uhci_hcd and address 12
            [11766.284036] usb 3-1: new full speed USB device using uhci_hcd and address 13
            [11776.529040] hub 3-0:1.0: unable to enumerate USB device on port 1
            [11983.429072] usb 3-1: new full speed USB device using uhci_hcd and address 14
            [12013.972403] usb 3-1: new full speed USB device using uhci_hcd and address 15
            [12044.517042] usb 3-1: new full speed USB device using uhci_hcd and address 16
            [12054.873041] usb 3-1: new full speed USB device using uhci_hcd and address 17
            [12065.117049] hub 3-0:1.0: unable to enumerate USB device on port 1
            [12978.317041] usb 1-3: new high speed USB device using ehci_hcd and address 16
            [12978.884046] usb 1-3: new high speed USB device using ehci_hcd and address 17
            [12983.888032] usb 1-3: new high speed USB device using ehci_hcd and address 18
            [12984.412035] usb 1-3: new high speed USB device using ehci_hcd and address 19
            [12984.676054] hub 1-0:1.0: unable to enumerate USB device on port 3
            [12984.944043] usb 3-1: new full speed USB device using uhci_hcd and address 18
            [12990.940073] hub 3-0:1.0: unable to enumerate USB device on port 1
            [12994.388044] usb 1-4: new high speed USB device using ehci_hcd and address 20
            [12994.957046] usb 1-4: new high speed USB device using ehci_hcd and address 21
            [12995.524041] usb 1-4: new high speed USB device using ehci_hcd and address 22
            [12995.904073] usb 1-4: new high speed USB device using ehci_hcd and address 23
            [12996.320063] hub 1-0:1.0: unable to enumerate USB device on port 4
            [12996.588042] usb 3-2: new full speed USB device using uhci_hcd and address 19
            [13027.132207] usb 3-2: new full speed USB device using uhci_hcd and address 20
            [13057.676047] usb 3-2: new full speed USB device using uhci_hcd and address 21
            [13068.029068] usb 3-2: new full speed USB device using uhci_hcd and address 22
            [13078.272064] hub 3-0:1.0: unable to enumerate USB device on port 2
            [14278.512029] usb 3-2: new full speed USB device using uhci_hcd and address 23
            [14309.057040] usb 3-2: new full speed USB device using uhci_hcd and address 24
            [14339.601076] usb 3-2: new full speed USB device using uhci_hcd and address 25
            [14349.956043] usb 3-2: new full speed USB device using uhci_hcd and address 26
            [14360.200044] hub 3-0:1.0: unable to enumerate USB device on port 2
            [15524.992043] usb 1-4: new high speed USB device using ehci_hcd and address 24
            [15525.560039] usb 1-4: new high speed USB device using ehci_hcd and address 25
            [15526.128036] usb 1-4: new high speed USB device using ehci_hcd and address 26
            [15526.652044] usb 1-4: new high speed USB device using ehci_hcd and address 27
            [15526.924048] hub 1-0:1.0: unable to enumerate USB device on port 4
            [15527.188045] usb 3-2: new full speed USB device using uhci_hcd and address 27
            [15557.733061] usb 3-2: new full speed USB device using uhci_hcd and address 28
            [15588.277037] usb 3-2: new full speed USB device using uhci_hcd and address 29
            [15598.632035] usb 3-2: new full speed USB device using uhci_hcd and address 30
            [15608.876756] hub 3-0:1.0: unable to enumerate USB device on port 2
            [16202.570095] usb 1-7: USB disconnect, address 8
            [16202.570679] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
            [16202.570857] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
            [16202.571020] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
            [16202.571174] option1 ttyUSB3: GSM modem (1-port) converter now disconnected from ttyUSB3
            [16214.549038] usb 1-8: new high speed USB device using ehci_hcd and address 28
            [16214.696067] scsi21 : SCSI emulation for USB Mass Storage devices
            [16214.697101] scsi22 : SCSI emulation for USB Mass Storage devices
            [16217.116042] usb 1-7: new high speed USB device using ehci_hcd and address 29
            [16217.251026] scsi23 : SCSI emulation for USB Mass Storage devices
            [16220.911314] usb 1-8: USB disconnect, address 28
            [16227.264044] usb 1-8: new high speed USB device using ehci_hcd and address 30
            [16227.412697] usb 1-8: GSM modem (1-port) converter now attached to ttyUSB0
            [16227.413258] usb 1-8: GSM modem (1-port) converter now attached to ttyUSB1
            [16227.413799] usb 1-8: GSM modem (1-port) converter now attached to ttyUSB2
            [16227.414429] usb 1-8: GSM modem (1-port) converter now attached to ttyUSB3
            [16227.415318] scsi28 : SCSI emulation for USB Mass Storage devices
            [16227.417312] scsi29 : SCSI emulation for USB Mass Storage devices
            [16274.313711] usb 1-7: USB disconnect, address 29
            [16276.564043] usb 1-7: new high speed USB device using ehci_hcd and address 31
            [16276.699466] scsi30 : SCSI emulation for USB Mass Storage devices
            [email protected]:~$ sudo modprobe usb-uhci
            FATAL: Module usb_uhci not found.
            [email protected]:~$ sudo modprobe usb-ohci
            FATAL: Module usb_ohci not found.
            [email protected]:~$ sudo modprobe usb-storage

            تعليق


            • #7
              ردي هذا على أول ردك. سأرى ردك الثاني.

              ----

              على حسب المخرجات أنت تستخدم:
              keyboard usb
              optical mouse usb
              modem 3g usb
              ثم pen drive usb لم يتعرف عليه "unable to enumerate USB device on port 1"

              هل هناك عتاد آخر لم أنتبه إليه ؟

              بافتراض أن pen drive usb تعمل (ليس بها عطل) ألا تضن أن المودم له يد في ذلك؟ لنتأكد
              أطفئ الجهاز، أزل usb modem، شغل الجهاز دون أن توصل المودم، بعد انتهاء الإقلاع تماما صل usb pen drive لترى هل تعرف عليها النظام أم لا؟

              على الهامش: كما هو معلوم، أغلب موديمات 3g تشتخدم نمط مزدوج: كوسيلة تخزين للقراءة فقط (كي يثبت التعريف على ويندوز تلقائيا) ثم نمط مودم (بعد أن يغر التعريف المثبت في أول وصل النمط تلقائيا من وسيلة تخزين إلى مودم) بحيث أشك في أن التعريف الحالي أو طريقة إعداده على لينوكس هي سبب المشكل.
              ArabicFOSS
              انضم إلى فريق المدونة و ساهم بما شئت وقتما شئت!

              تعليق


              • #8
                المشاركة الأصلية بواسطة محمد البردعي مشاهدة المشاركة
                ردي هذا على أول ردك. سأرى ردك الثاني.

                ----

                على حسب المخرجات أنت تستخدم:
                keyboard usb
                optical mouse usb
                modem 3g usb
                ثم pen drive usb لم يتعرف عليه "unable to enumerate USB device on port 1"

                هل هناك عتاد آخر لم أنتبه إليه ؟

                بافتراض أن pen drive usb تعمل (ليس بها عطل) ألا تضن أن المودم له يد في ذلك؟ لنتأكد
                أطفئ الجهاز، أزل usb modem، شغل الجهاز دون أن توصل المودم، بعد انتهاء الإقلاع تماما صل usb pen drive لترى هل تعرف عليها النظام أم لا؟

                على الهامش: كما هو معلوم، أغلب موديمات 3g تشتخدم نمط مزدوج: كوسيلة تخزين للقراءة فقط (كي يثبت التعريف على ويندوز تلقائيا) ثم نمط مودم (بعد أن يغر التعريف المثبت في أول وصل النمط تلقائيا من وسيلة تخزين إلى مودم) بحيث أشك في أن التعريف الحالي أو طريقة إعداده على لينوكس هي سبب المشكل.
                عمل لكن نصف عمل
                يعني
                قمت بإخراج الموديم و عملت إعادة التشغيل للجهاز وعندما اشتغل الجهاز أدخلت الpen drive بشكل سليم
                لكن أردت أن أتأكد هل تعمل بشكل كامل فعملت إخراج السواقة بأمان فأخرجتها وأعدت إدخالها من جديد فلم تعمل

                تعليق


                • #9
                  ستعيد الكرة مرة ثانية لكن هذه المرة عند وصل pen drive لأول مرة ستنفذ ما يلي و تكتب المخرجات
                  كود:
                  dmesg | tail
                  ثم تزيلها بطريقة سليمة متبوع مباشرة بالأمرين التالين و تكتب المخرجات هنا.
                  كود:
                  dmesg | tail
                  tail /var/log/messages
                  ArabicFOSS
                  انضم إلى فريق المدونة و ساهم بما شئت وقتما شئت!

                  تعليق


                  • #10
                    المشاركة الأصلية بواسطة محمد البردعي مشاهدة المشاركة
                    ستعيد الكرة مرة ثانية لكن هذه المرة عند وصل pen drive لأول مرة ستنفذ ما يلي و تكتب المخرجات
                    كود:
                    dmesg | tail
                    ثم تزيلها بطريقة سليمة متبوع مباشرة بالأمرين التالين و تكتب المخرجات هنا.
                    كود:
                    dmesg | tail
                    tail /var/log/messages
                    لقد قمت بما أمرت وهاهي المخرجات
                    كود:
                    [email protected]:~$ dmesg | tail
                    [   81.136685] scsi 4:0:0:0: Direct-Access     Kingston DataTraveler 2.0 PMAP PQ: 0 ANSI: 0 CCS
                    [   81.138088] sd 4:0:0:0: Attached scsi generic sg2 type 0
                    [   83.379141] sd 4:0:0:0: [sdb] 7936000 512-byte logical blocks: (4.06 GB/3.78 GiB)
                    [   83.379628] sd 4:0:0:0: [sdb] Write Protect is off
                    [   83.379633] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00
                    [   83.379636] sd 4:0:0:0: [sdb] Assuming drive cache: write through
                    [   83.381899] sd 4:0:0:0: [sdb] Assuming drive cache: write through
                    [   83.381910]  sdb: sdb1 sdb2
                    [   83.431028] sd 4:0:0:0: [sdb] Assuming drive cache: write through
                    [   83.431042] sd 4:0:0:0: [sdb] Attached SCSI removable disk
                    كود:
                    [email protected]:~$ dmesg | tail
                    [   83.431028] sd 4:0:0:0: [sdb] Assuming drive cache: write through
                    [   83.431042] sd 4:0:0:0: [sdb] Attached SCSI removable disk
                    [  212.276054] usb 1-7: USB disconnect, address 4
                    [  228.273030] EXT4-fs (sda6): mounted filesystem with ordered data mode
                    [  320.096022] usb 1-7: new high speed USB device using ehci_hcd and address 5
                    [  320.231144] usb 1-7: configuration #1 chosen from 1 choice
                    [  320.231565] scsi5 : SCSI emulation for USB Mass Storage devices
                    [  320.231897] usb-storage: device found at 5
                    [  320.231902] usb-storage: waiting for device to settle before scanning
                    [  325.431543] usb 1-7: USB disconnect, address 5
                    [email protected]:~$ tail /var/log/messages
                    Nov  7 18:21:42 assilah-desktop kernel: [   83.379141] sd 4:0:0:0: [sdb] 7936000 512-byte logical blocks: (4.06 GB/3.78 GiB)
                    Nov  7 18:21:42 assilah-desktop kernel: [   83.379628] sd 4:0:0:0: [sdb] Write Protect is off
                    Nov  7 18:21:42 assilah-desktop kernel: [   83.381910]  sdb: sdb1 sdb2
                    Nov  7 18:21:42 assilah-desktop kernel: [   83.431042] sd 4:0:0:0: [sdb] Attached SCSI removable disk
                    Nov  7 18:23:51 assilah-desktop kernel: [  212.276054] usb 1-7: USB disconnect, address 4
                    Nov  7 18:24:07 assilah-desktop kernel: [  228.273030] EXT4-fs (sda6): mounted filesystem with ordered data mode
                    Nov  7 18:25:39 assilah-desktop kernel: [  320.096022] usb 1-7: new high speed USB device using ehci_hcd and address 5
                    Nov  7 18:25:39 assilah-desktop kernel: [  320.231144] usb 1-7: configuration #1 chosen from 1 choice
                    Nov  7 18:25:39 assilah-desktop kernel: [  320.231565] scsi5 : SCSI emulation for USB Mass Storage devices
                    Nov  7 18:25:44 assilah-desktop kernel: [  325.431543] usb 1-7: USB disconnect, address 5
                    [email protected]:~$

                    تعليق


                    • #11
                      لم أستطع اكتشاف مصدر المشكلة. هل تملك usb pen drive آخر بمصنع مختلف تستخدمه و يعمل من دون مشاكل أم أن كل الأنواع لا يتعرف عليها؟

                      أيضا، هل تستطيع أن تذكر المصتع و رقم المنتج بالتدقيق، الخاص بالـ usb pen drive كي أبحث عن مشكلة مشابه لحالتك في النت؟ ربما usb pen drive غير متوافق أو يحتاج إلى اعدادات خاصة.

                      ثم، هل لك أن تذكر و تشير لي الطريقة التي اعتمدت عليها لتثبيت المودم؟
                      ArabicFOSS
                      انضم إلى فريق المدونة و ساهم بما شئت وقتما شئت!

                      تعليق


                      • #12
                        المشاركة الأصلية بواسطة محمد البردعي مشاهدة المشاركة
                        لم أستطع اكتشاف مصدر المشكلة. هل تملك usb pen drive آخر بمصنع مختلف تستخدمه و يعمل من دون مشاكل أم أن كل الأنواع لا يتعرف عليها؟

                        أيضا، هل تستطيع أن تذكر المصتع و رقم المنتج بالتدقيق، الخاص بالـ usb pen drive كي أبحث عن مشكلة مشابه لحالتك في النت؟ ربما usb pen drive غير متوافق أو يحتاج إلى اعدادات خاصة.

                        ثم، هل لك أن تذكر و تشير لي الطريقة التي اعتمدت عليها لتثبيت المودم؟
                        نعم أملك usb pendrive اخر
                        1 - لدي إصدار kingstone DTI

                        2 - وإصدار kingstone DT100

                        -----*****-----
                        بالنسبة للطريقة التي اعتمدتها لتثبيت الموديم
                        https://wiki.ubuntu.com/MoroccanTeam...s/Huawei_E1550

                        تعليق


                        • #13
                          كلاهما لا تعمل !؟
                          ArabicFOSS
                          انضم إلى فريق المدونة و ساهم بما شئت وقتما شئت!

                          تعليق


                          • #14
                            المشاركة الأصلية بواسطة محمد البردعي مشاهدة المشاركة
                            كلاهما لا تعمل !؟
                            نعم .. والعجبب في الأمر أنها تعمل في جهاز آخر به اوبونتو ولا تعمل بجهازي
                            لكن - كما ذكرت سابقا - كانت تعمل عندي في البداية لكن الان لم تعد تعمل .
                            لا أعرف هل بسبب التحديثات أو شيء اخر

                            تعليق


                            • #15
                              ربما. جرّب الإقلاع بنواة قديمة
                              عبدالرحيم الفاخوري -- abdilra7eem
                              IRC: Fakhouri
                              فلسطين
                              مترجم ومبرمج ويب وفني شبكات وخوادم يحب البطاريق

                              كتاب الإدارة المتقدمة لجنو/لينكس:
                              https://librebooks.org/gnu-linux-adv...dministration/

                              تعليق

                              يعمل...
                              X