إعـــــــلان

تقليص
لا يوجد إعلان حتى الآن.

تعريف Ati عى مندريفا ٢٠٠٨ بالتفصيل

تقليص
X
 
  • تصفية - فلترة
  • الوقت
  • عرض
إلغاء تحديد الكل
مشاركات جديدة

  • تعريف Ati عى مندريفا ٢٠٠٨ بالتفصيل

    وجدت موضوع ممتاز ومفصل يشرح طريقة تعريف كروت ati على منتدى مندريفا واحببت أن انقل اهم النقاط في الموضوع :
    كود:
    Installing the new ATI drivers on 2008 is not an easy process compared
     to 2007/1.. On a clean install of 2008 I had to go with the default 8.40 drivers
     and configure the card through the MCC then open the software manager remove
     all the related *latest packages for the ones listed below enable the main
     contrib and non-free backports finally reboot to failsafe
    type init 3 log in at the prompt su to root and do the following.
    1.urpme x11-driver-video-fglrx 8.40.4-7mdv2008.0
    2. urpme dkms-fglrx 8.40.4-7mdv2008.0
    3.urpme fglrx-control-center 8.40.4-7mdv2008.0
    4. fglrx-kernel-2.622.9-desktop-1mdv
    then
    1.urpmi dkms-fglrx-hd2000 8.42.3-4ndv2008.0
    2.urpmi fglrx-hd2000-control-center 8.40.4-7mdv2008.0
    3. urpmi x11-driver-video-fglrx-hd2000 8.40.4-7mdv2008.0
    
    reboot..
    
    I had working 3-D then but I also had the watermark issue so I had to
    download
     the ati-driver-installer-8.42.3-x86.x86_64.run from ATI and from a konsole type
     chmod +x ati-driver-installer-8.42.3-x86.x86_64.run then ./ati-driver-installer-8.42.3-x86.x86_64.run --extract
    then from the run command did kdesu konqueror navigate to the extracted fglrx-install folder browse
     to the /common/etc/ati sub folder
    and copy the contents to /etc/ati... I think I only needed
     the
    logo_mask.xbm.example and the signature files but I was aggravated
    by then and copied the entire contents and rebooted and the watermark was gone.
    Then I editied the xorg.conf to enable AIGLX and composite.
    
    Under Section "ServerLayout"
    Option "AIGLX" "on"
    
    Under Section "ServerFlags"
    Option "AIGLX" "true"
    
    Created
    
    Section "Extensions"
    Option "Composite" "Enable"
    EndSection
    
    Reboot
    
    Now I am able to run compiz-fusion in native mode.
    No other method I had used previously to install the drivers would work and always resulted in mesa for 3-D
    
    AW posted this thread yesterday http://forum.mandriva.com/viewtopic.php?t=75822
    That should make it much easier... however... I don't understand why you need to install the old drivers and overlay the new ones...I never liked doing that in windows either...
    
    Also I had to edit the /boot/grub/menu.lst and change
    splash=silent to splash=verbose otherwise x would hang when logging out/switching users. No idea if this has been fixed with AW's new method of installing the drivers.
    
    *Edit*
    When I did the urpme listed 1st a package got removed as a dependency I couldn't remember what it was but it was related to the 8.40 drivers.. I think it was the dkms package but wasn't sure so I listed it anyways.
    وفي حالة رغبتك اﻻستزادة يمكن مراجعة الموضوع اﻻصلي على رابط مندريفا :
    http://forum.mandriva.com/viewtopic.php?t=75533

  • #2
    وعليكم السلام

    لا عاد تنسى الايقونه ياسلفر علشان ما اقفل .. الموضوع ..


    دمت بخير ...

    bAD3R
    :argeeleh:
    Twitter
    : @Linux4SA

    تعليق


    • #3
      شكرا لك أخوي على الشرح
      والله يعطيك العافية

      -------------
      bAD3R حاسك شرطي مرور خخخخخخخخخخ

      تعليق


      • #4
        المشاركة الأصلية بواسطة BAD3R مشاهدة المشاركة
        وعليكم السلام

        لا عاد تنسى الايقونه ياسلفر علشان ما اقفل .. الموضوع ..


        دمت بخير ...

        bAD3R
        آسف وشكراً ﻷنك لم تقفل الموضوع .

        تعليق

        يعمل...
        X